nitrous and a aluminum block?

[whitetrash]

Never seen a stock ls1?!?!


Oh and you could buy my rods and pistons and be good to 800~

[racrguy]

wut???????????

Thanks. I was trying to figure out what the fuck he's talking about too.

[Swamp Donkey]

I'd be more concerned with blowing the welds on the intake.

[91CoupeMike]

Thanks. I was trying to figure out what the fuck he's talking about too.

It holds some weight a actually.

The stock oil pump drive gears are common in grenading on modulars. They say its from using under drive pulleys. Something with the harmonic balancer configuration and how it effects the wear and abuse on the drive gears.

That aside,

I'm working getting a plate for my systemax. Planning to spray 150.

So now I need a msd box with a 2step, window switch and maybe fuel pump. Hoping it fits under the stock hood.

Amongst other things, I think that should scoot. ~500rwhp

[racrguy]

It holds some weight a actually.

The stock oil pump drive gears are common in grenading on modulars. They say its from using under drive pulleys. Something with the harmonic balancer configuration and how it effects the wear and abuse on the drive gears

Who is they? I've never heard of that before, and it sounds fucking stupid.

[uglydogo]

Who is they? I've never heard of that before, and it sounds fucking stupid.

Why don't you shut the fuck up!! I Damn sure don't need your "opinion", or your dumbest comment. If don't understand what people are saying go somewhere else

[uglydogo]

No "need" for a tune at only 100 shot... What car is this going on? I assume its a dry shot since you're asking about the injectors? Stock will be fine. Don't use U/D pullies on a modular motor... Read up on them and you'll find out why.

Why don't I need a tune ? I'm not sure about wet or a dry witch one would do best in this application?

[whitetrash]

Why don't you shut the fuck up!! I Damn sure don't need your "opinion", or your dumbest comment. If don't understand what people are saying go somewhere else

English mother fucker! do you speak it?


because you damn sure don't type it.

[racrguy]

Why don't you shut the fuck up!! I Damn sure don't need your "opinion", or your dumbest comment. If don't understand what people are saying go somewhere else

I'm sorry. Who the fuck are you again? Oh, wait. You're the guy who can't fucking figure out if it's ok to put some nitrous through an aluminum 4.6. You are the FIRST person to ever try that. Nobody's been doing it for over a decade. Never. Fucking. Happened.

Here's the cool thing about my opinions, they aren't opinions...

[uglydogo]

English mother fucker! do you speak it?


because you damn sure don't type it.

Your right BITCH! I don't need your need you god damn comments. I'm just looking for some thoughts on some things I'm working on. If you don't have the answer I need, why are you commenting on what everyone is saying.

You know what FUCK YOU !! YOU UNDERSTAND THAT ?

[BMCSean]

[uglydogo]

I'm sorry. Who the fuck are you again? Oh, wait. You're the guy who can't fucking figure out if it's ok to put some nitrous through an aluminum 4.6. You are the FIRST person to ever try that. Nobody's been doing it for over a decade. Never. Fucking. Happened.

Here's the cool thing about my opinions, they aren't opinions...

I understand people have been doing it forever. But I haven't. I didn't think it was going to be this big of a deaI just looking for some advise I have never ran nitrous on anything. I wouldn't ask a question that I already know the answer to.

[Wish4svts]

Who is they? I've never heard of that before, and it sounds fucking stupid.

. It's been well discussed for a long while now that U/D pullies and modular motors don't mix. "They", would be John mihovetz, Al Pappito, Sean hyland are a few whom all discourage U/Ds.

Here's the cool thing about my opinions, they aren't opinions...

This shit was funny as hell!

[crapstang]

Who is they? I've never heard of that before, and it sounds fucking stupid.

I don't know how you haven't heard of this being a problem. IDK if you are into the modular stuff or not, but it's commonplace for pump gears to come apart due to the vibrations.
One of the many examples:

http://www.svtperformance.com/forums/new-edge-cobras-51/724772-bbk-piggy-back-pulleys-make-oil-pump-go-kaboom.html

[racrguy]

. It's been well discussed for a long while now that U/D pullies and modular motors don't mix. "They", would be John mihovetz, Al Pappito, Sean hyland are a few whom all discourage U/Ds.


This shit was funny as hell!

I don't know how you haven't heard of this being a problem. IDK if you are into the modular stuff or not, but it's commonplace for pump gears to come apart due to the vibrations.
One of the many examples:

He said drive gears. I've never heard of anyone having problems with drive gears in ANY form of motor. Now, the gears inside the pump taking a shit I've heard, seen, and had happen to me.