I have this system on my car and can walk you through the input/output stuff if you need help.
I may take you up on that. It might take a while before I get a good chance to get it all in and ready to fire up again though.
I found Holley's own forum to be extremely helpful and fast to respond. When I was planning and mapping this system out while still in Afg, I had tons of stupid questions. Some mod named Danny C(something) is like a Holley EFI savant.
Keyed valet switch with 4 positions for 4 different tunes
Air temps and coolant temps
NTK O2 sensor
Boost control
Labeled harness and each connection.
..for the GM coil-n-plug coils. Looking at it on the table, I could have built this myself for a tenth of the price and I think I going to swap out the GM plug anyways to a Duetsch (8pin) since that is what is on my coils already.
Ford MPFI Injector sub harness
Last edited by KBScobravert; 04-04-2014, 05:05 PM.
I may take you up on that. It might take a while before I get a good chance to get it all in and ready to fire up again though.
I found Holley's own forum to be extremely helpful and fast to respond. When I was planning and mapping this system out while still in Afg, I had tons of stupid questions. Some mod named Danny C(something) is like a Holley EFI savant.
No problem at all. I don't mind helping. What kind of IAC are you using? Also, did you get a 5 bar map sensor?
Yep Danny C is very very smart with the Holley. He actually doesn't work for Holley either. You would think he would with all the knowledge he has on the system.
No problem at all. I don't mind helping. What kind of IAC are you using? Also, did you get a 5 bar map sensor?
Yep Danny C is very very smart with the Holley. He actually doesn't work for Holley either. You would think he would with all the knowledge he has on the system.
I have a 5bar (holley) for MAP and a 3.5bar(AEM) for dome pressure.
For IAC I want to use the Ford 2 wire. Danny C says it is better than the gm the harness is pre built for. Faster and more accurate.
I have a 5bar (holley) for MAP and a 3.5bar(AEM) for dome pressure.
For IAC I want to use the Ford 2 wire. Danny C says it is better than the gm the harness is pre built for. Faster and more accurate.
You will have to put a new connector on the harness for the 5 bar map... And my harness was pre-pinned for a Chrysler IAC. I used a GM IAC on mine because my throttle body is off a LS car.
Repinning the IAC is easy... Pull the grey wire holder off the back of the black plug, then pop the purple cover off the other end. This will expose the holding clips. Get a small pick or screw driver and just barely pop them up while pulling the wire from the other end. The wire will come out very smoothly with the connector still attached. Move the wire over to the correct spot depending on what IAC you use.
Just ordered up Holley's 83pound injectors http://www.holley.com/522-838.asp to step down from the Trickflow 120s.
Even on the E85 and at 650rwhp and 14pounds of boost, I was only in the 62% duty cycle
Going from E85 to 93oct. And may try a E85 tune on the 83s just to see.
Nice thing about using their injector, the data is all in the ECU already so no guessing what is what again.
Also ordered their CNP coil built like the LQ9 heat sink truck coils I already have but built for their EFI. http://www.holley.com/556-112.asp
This is turning into a complete Holley EFI system down to all their sensors, wiring etc. It better start and run right off the bat.
I am not real set on the 556-112 coils but to have a system that was designed, built and sold to work together. But my sister already has them coming so no punking out now.
Comment