Tweet
Is that a decent deal though? I will end up reloading, I just don't want to start off reloading it until I gain more experience with the round. If it matters it's a 7.5" 1/7 twist supressed.
-
"You don't so much drive it, more like poke it with a sharp stick and channel the fury when you piss it off."
FFL & LTC Instructor
http://firstresponsefirearms.com/
Factory Five MK4 Cobra
Build thread-http://www.dfwmustangs.net/forums/showthread.php?t=17889
http://s1124.photobucket.com/albums/l571/BlitzAttack65/
www.wix.com/cdurhamwot/blitzattack-mk4-build
sigpic -
I can't really comment, I haven't bought ammo in years. I load that exact round for $6.50 per 50."When the people find that they can vote themselves money, that will herald the end of the republic." -Benjamin Franklin
"A democracy will continue to exist up until the time that voters discover that they can vote themselves generous gifts from the public treasury." -Alexander Fraser TytlerComment
-
I need to get on board with that setup!Originally posted by CJ View Post
The rounds are pricey but about on par with what i pay for 30.06 and a big reason I went the .300 route is for huntingComment
-
You can get the 220gr UMC load for $15-$20/20, but that's as cheap as it gets.ZOMBIE REAGAN FOR PRESIDENT 2016!!! hehComment
-
its because the bullets are .40-.50/each. Hard to make that cheap. But I'm working on it."When the people find that they can vote themselves money, that will herald the end of the republic." -Benjamin Franklin
"A democracy will continue to exist up until the time that voters discover that they can vote themselves generous gifts from the public treasury." -Alexander Fraser TytlerComment
-
I don't like Republicans, but I really FUCKING hate Democrats.
Sex with an Asian woman is great, but 30 minutes later you're horny again.Comment
-
Any ideas here. I have a 7.5" barrel, with an AAC 7.62sd. With the 7" rail installed it will not allow the can to seat fully on the flash hider, and the can doesn't fit inside the rail. I would like to try and make this work without ordering a new rail or barrel. That being said can I use a stackable muzzle washer, or should I shorten the handguard a 1/2"?
"You don't so much drive it, more like poke it with a sharp stick and channel the fury when you piss it off."
FFL & LTC Instructor
http://firstresponsefirearms.com/
Factory Five MK4 Cobra
Build thread-http://www.dfwmustangs.net/forums/showthread.php?t=17889
http://s1124.photobucket.com/albums/l571/BlitzAttack65/
www.wix.com/cdurhamwot/blitzattack-mk4-build
sigpicComment
-
Chuck it up in a lathe, and cut the end off until it fits.ZOMBIE REAGAN FOR PRESIDENT 2016!!! hehComment
-
The 762-SD sits about a guarter inch from the back surface of the flash higher when fully seated so you only option is going to be to cut the handguard. It looks like you may even have to come as far back as that first set of threaded holes.
I worry that I may have to deal with the same issue when mine shows up.
Is your muzzle device the deep or standard socket type?Comment
-
Not sure if it's the deep or standard. Package doesn't say, it's the AAC blackout 51t flash hider."You don't so much drive it, more like poke it with a sharp stick and channel the fury when you piss it off."
FFL & LTC Instructor
http://firstresponsefirearms.com/
Factory Five MK4 Cobra
Build thread-http://www.dfwmustangs.net/forums/showthread.php?t=17889
http://s1124.photobucket.com/albums/l571/BlitzAttack65/
www.wix.com/cdurhamwot/blitzattack-mk4-build
sigpicComment
-
Comment
-
The standard for suppressors is 1.5" OD, so any rail worth it's salt should have a 1.6" ID
"When the people find that they can vote themselves money, that will herald the end of the republic." -Benjamin Franklin
"A democracy will continue to exist up until the time that voters discover that they can vote themselves generous gifts from the public treasury." -Alexander Fraser TytlerComment
-
51t sucks for putting inside railsComment
-
The rail is a Midwest industries with an OD of 1.5. I didn't plan on it going in the rail due to the 51t. And it's the deep socket FH."You don't so much drive it, more like poke it with a sharp stick and channel the fury when you piss it off."
FFL & LTC Instructor
http://firstresponsefirearms.com/
Factory Five MK4 Cobra
Build thread-http://www.dfwmustangs.net/forums/showthread.php?t=17889
http://s1124.photobucket.com/albums/l571/BlitzAttack65/
www.wix.com/cdurhamwot/blitzattack-mk4-build
sigpicComment
-
Grab a standard and see where it gets you.Comment
Comment