Announcement

Collapse
No announcement yet.

70+70=?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #46
    Originally posted by Broncojohnny View Post
    Did I say it wasn't fun? I just said videos of people racing from a roll are fucking played out and lame.
    To each is to their own. It's whatever moves you. I like all racing, it's all fun to me.

    Comment


    • #47
      Originally posted by "MrEd" View Post
      Z06 guy probably sold the vette and went out and bought a nova.
      Steve im far from a guy that would just come on here and say,
      MY BUDDIES CAR IS FASTER THAN A ZO6,with out knowing for sure.
      unless i knew the facts of coarse....
      no the nova was not doing any road coarses,120-0,0-120,etc etc etc test.
      it was from a roll which thats what everyone does these ,am i right and as a matter of fact,it was from a 30mph roll up to a 120 and the nova jump out on the vette by 1 car then the nova ran out of gear,if nova had the gear he could have really waxed the vette.
      Nova went low 12s in street trim with a 355 motor n/a.
      so now with a d1 in street trim,ha if it could ever hook its a easy low 10s car.
      So a D1 drops 2 seconds off the 1/4 time. Got it, i'm taking notes here

      What's yer opinion on a 3/4 cam? Wut kinda ET's could I be spectin to gain from that bad boy

      Comment


      • #48
        Originally posted by slownbmta View Post
        So a D1 drops 2 seconds off the 1/4 time. Got it, i'm taking notes here

        What's yer opinion on a 3/4 cam? Wut kinda ET's could I be spectin to gain from that bad boy
        3/4 cams is the way to go! lmao

        Comment


        • #49
          Originally posted by slownbmta View Post
          So a D1 drops 2 seconds off the 1/4 time. Got it, i'm taking notes here

          What's yer opinion on a 3/4 cam? Wut kinda ET's could I be spectin to gain from that bad boy
          Yep...
          All from a Goodwrench 350 and the cam ha..
          Its 2 4cyl cams welded together.
          Take notes BITCHES!!!

          Comment


          • #50
            Originally posted by "MrEd" View Post
            Yep...
            All from a Goodwrench 350 and the cam ha..
            Its 2 4cyl cams welded together.
            Take notes BITCHES!!!
            Don't be telling my secrets.

            Comment


            • #51
              Originally posted by slownbmta View Post
              So a D1 drops 2 seconds off the 1/4 time. Got it, i'm taking notes here

              What's yer opinion on a 3/4 cam? Wut kinda ET's could I be spectin to gain from that bad boy
              The engine was kinda a turd NA. This is what happens when you run a low compression motor with a "3/4" race cam from Steve Morris without the power adder. But I am sure you realize that.

              Comment


              • #52
                Oops I did it again.

                Comment


                • #53
                  Man no need to explain to them how easy it is to build a blower motor,dfwmustangs people.
                  THEY ALREADY KNOW, BITCHES........
                  Last edited by "MrEd"; 08-31-2011, 06:40 AM.

                  Comment


                  • #54
                    When you can make a nitrous motor run 10.0's in a 4000 pound car in the heat and then turn the bottle on.....well you get where I'm going.
                    Doing enough racing for 99% of the board!

                    Comment


                    • #55
                      Originally posted by OrangeChevyII View Post
                      When you can make a nitrous motor run 10.0's in a 4000 pound car in the heat and then turn the bottle on.....well you get where I'm going.
                      That Nova should haul some serious ass being so much lighter! Can't wait to see it run.

                      Comment


                      • #56
                        I'm not putting that motor in my car, I wanna driver.
                        Doing enough racing for 99% of the board!

                        Comment

                        Working...
                        X