BRR's newest project: Project Stepchild

[RuStYpNuS]

its been a long time coming. A lot of you know me from my blue four eye'd fox. Long story short i sold it to TannerM.....then he sold it off and profited and now driving "Aunt Flo", CJs old F100. Well this is my newest project and kind of a wild barn find so to speak. I came across it on craigslist a while back and after about a month of cold calling the guy with no responses he one day answered and i went that night to check it out. came back 30 days later and left with the truck. It sat in his shop for 5 years and he eventually decided to file a mechanics lien as the original owner never came and got it (hence the 30 days) i got a smoking deal on it so i couldnt pass it up.

1994 Ford F150 Lightning #425 of 1382
151k and 100% stock and original with the exception of the tires, brakes, shocks, and ecu (reason for it being in the shop in the first place)

Needs: Minor dents and dings fixed and paint although if it werent for the dents and scratches the paint looks really good
AC compressor
TIRES!!!!! Its got may-pops on it now
Need door key cut
Radio
Antenna
Windshield (has crack)

Like i said Project but it has ZERO leaks and doesnt miss a beat. hasnt been stickered since 06. pulled out of QT today headed to the car wash and got it side ways

I will update this thread for the BRR mafia as it progresses.

here are the pics.

[RuStYpNuS]

[RuStYpNuS]

Fast forward to November 2012. Wish i would have kept track of what i have done and when but for the most part here is my list of parts either on or going on the truck very soon.

Suspension:
Prothane Bushing kit= - Master kit RED
New power steering gear, ball joints and tie rod ends
Rancho Gen 2 Long bars
DJM 3/4 Dream Beams

Exhaust:
Mac 1-5/8 x 2.5" Mustang AOD Longtube headers- Ceramic Coated in/out heat wrapped
Spintech Mufflers Dumped

Wheels & Tires:
Polished stockers
Toyo Proxies 275/60/17s

Transmission:
Circle D Valvebody
Derale Cooling TransPan
OEM trans pan gasket
StayPut Filter Clip

Rear End:
31 spline Eaton Locker
FRPP Crush Sleeve Eliminator
unknown brand 4.56 gears
ARP Diff cap Studs
Ford Racing Axle Girdle
New Bearings and Seals from end to end

Engine:
Summit Racing Brand 75mm polished throttle body
Trick Flow 75mm egr delete spacer
Ported GT40 X305 58cc aluminum heads
Ford Racing valve stem seals
GT40 upper port matched to throttle body-Ceramic Coated
GT40 lower port matched to heads-Ceramic Coated
Accesory Brackets powdercoated gloss black
Lightning plaque powdercoated gloss black
Coil bracket ceramic coated
Proform 1.6 RRs
FRPP roller conversion kit
FRPP M-9000-L58 Mass Air Conversion Kit
Comp Cams NX264 Cam
King Race Rod and Main Bearings
ARP WaveLoc Rod bolts
ARP Main Cap bolts
New seals front to rear top to bottom
FRPP Performance top end gasket kit
Professional Products 28oz balancer
FMS SVO Powerdyne BD11a supercharger kit
Windstar Dual Electric fans
130a 3g Alternator

Electronics:
Moates QH tuned via the DIABOLICal genius on AKC0
Innovate MTX-L Wideband

ok so yesterday, Saturday Nov 3, 2012 was the start of my anxiety






Can you say Quakersludge??


nothing like a little crack to get the morning going lol


wish i would have taken pics of the locker and gears installed before the girdle went on....sho wuz purdy



as of now the rear end is put back in and only needs the brakes reinstalled and the longbars reinstalled then its finished.

pulling the block out next weekend since we found all the sludge and gunk and have decided it will get new paint bearings seals and arp hardware throughout it as well as a new oil pump. we also discovered the distributor was TRASH....upper bearing is shot and it grinds wobbles and snags on something inside....so a new one of those will be underway as well.

I think we got a lot done considering i removed stripped and painted the rear end yesterday and was able to install the locker gears and new bearings and hardware as well as set up the gears and strip down the engine to the block.

Stay Tuned

11/8/2012 Dropped off Upper and lower intake, coil bracket, and longtubes to get ceramic coated. Accessory brackets and intake plaque will be gloss black and i will paint the lighting lettering silver once he finishes...@ 475$ its a bargain

[80coupe]

looking good Scott!

[dumpycapri85]

Nice but it ain't no four eye . Where are the kids gonna sit . Lol

[RuStYpNuS]

jax will ride shotgun and chloe can ride in the bowtie with her bowtie lovin momma

[kingjason]

Nice but it ain't no four eye . Where are the kids gonna sit . Lol

He can get the ole bench seat turned around in the bed mod. Good for three kids at least.

[Denny]

Helloooooooo gas stations!

I love the shit out of those trucks, but damn that gas mileage. Looks like a fun lil project, though.

[RuStYpNuS]

yea at least it wont be my daily........although the more i drive it the more im kinda like f the gas prices.....its almost worth it......gas is slowly dropping in prices so who knows. i need to prioritize the list of things its needs first

Title
Tires
Tags
Window motor
AC
Gear Selector cable
Radio/antenna
Header back Bassani kit

[LaserSVT]

I havent seen one of them Alpine 3-CD changers in a long freakin time.

Always had a soft spot for the first gens. Wanted to get one again when Trucks did that STS turbo one a couple years back.

[ozzeran]

I want constant updates!

I love those trucks, I forgot what the factory intake looked like on those, very restrictive (not the manifold)

[projectPONY]

great truck, congrats.



God I miss my L!

[dumpycapri85]

Scott will have this thing clean and mean in no time . You know I want one to .

[Jimbo]

Badass, subscribing.

[Beaterjuiced]

Nice